Differences Between Starting From Scratch And A Franchise

Are you contemplating starting a new business? There are some things that youre definitely going to need to think about before heading down that road. Lets talk about a few very important options youll need to consider.

The most difficult part of any new business is getting it started. Youll have a lot of administrative stuff to figure out, and youll need to start getting clients right away. Youve undoubtedly heard that 80% or so of new businesses fail in the first 2 years or so. This number will fluctuate depending on the industry and where you get your numbers from, but in the end its been shown the most new businesses fail.

So why do most new businesses fail? Well, there are a couple of common reasons. One is that a new business fails to advertise like it should. So they fade into nonexistence. This ties into the second common problem which is just running out of money. There are a number of causes for this, but if you run out of money you are pretty much out of business.

Im not trying to demotivate you. But you need to be aware that there are things you can do to improve your chances. Lets look at one.

One way to give yourself a better chance of surviving as a new business is to start as a franchise instead of a brand new business. There are a couple of reasons why this is a good option. First of all, the franchise will teach you how to run their system. They already have a proven track record that will get you started right.

Another great benefit of starting a franchise is you get brand recognition. No one has heard of Bills Best Burgers, but they have heard of McDonalds, Burger King, and a number of other franchises. With all the advertising the franchise does nationally you get immediate recognition when you open your store.

You dont have to just open a franchise in the food industry. You can also open them in just about any other industry you can think of. There are franchises in electronics, batteries, ink cartridges, clothing, and tons of other industries.

So there you have it. Do you start everything from scratch or do you start a franchise? One is definitely a more expensive option, but you will have a much better chance of long term success.

Make Money Online – An Amazing 5 Step Formula Shows You How

Follow these super simple 5 steps for making money online and get ahead of 95 per cent of other marketers.

*Step 1* Target a large group of people

First you need to research your intended market. You need find a reasonably large number of targeted individuals who have money to spend and a problem that needs solving. To make money online you need to offer a great product, or service, that solves a problem for them.

You need to research:

(a)What are people searching for online? (b)How many people are searching online for a solution to their particular problem?

First though, what should you be marketing in your proposed new online business?

Ideally, you should market something that you have a keen interest in, this will keep you motivated. You can find out what people are searching for at adwords.google.com/select/KeywordToolExternal and here inventory.overture.com/d/searchinventory/suggestion/

*Step 2* Locate a great product

Once you have researched your target market, it is time to quickly locate your products or services. If you have your own product great, if not then there are plenty of options to sell, or resell other peoples products.

There are thousands of products you can find quickly. However, marketing and selling a really good product needs a little more attention (you could create your own but you want to get started fast, right?)

Next…locate your products You can choose to promote physical products or digital online products. Digital products cover many different areas of interest and are incredibly profitable. There are no delivery costs with digital download products they are a good choice to promote as most offer good margins.

Here are some prime resources for sourcing digital products:

1. paydotcom.com 2. clickbank.com 3. cj.com

Here are some prime sources for physical products:

1. doba.com 2. alibaba.com 3. worldwidebrands.com

There are other resources but the above sites are a great place to start for all types of fast selling digital download products.

*Step 3* Market to your target audience

Now you have researched your chosen market, and located great products you can sell, its time to reach out and grab those targeted individuals.

So how are you going to attract your hungry buyers at little or no cost?

You MUST reach your target market in a way that allows you still to make a good profit. There are many ways to achieve this (that is another book in itself) but Im going to show you the most cost effective way to market almost any product or service online. In fact it is so cost effective it wont cost you anything (just a little time set aside to complete it).

So what is this free method?

Articles. Yes article marketing is THE most powerful way to attract ready made buyers to your site for little or NO cost. You basically write something that is informative and of interest to readers of your target market, then submit your articles to directories to get them published.

Get the maximum benefits of insurance policies in Singapore

If a person has family members who are dependent on him then in such situation, a life insurance policy can be a very useful tool to ensure the protection of one’s family along with peace of mind, in case of any unfortunate incident risking the life.

With the realization of the importance of life insurance, the people of Singapore are becoming more and more aware to derive the benefits of a good life insurance policy. Almost all the policies linked to life insurance in Singapore, offer many benefits that can be derived from several of the three simple types.

Term Life Insurance Singapore

This type of insurance provides benefits in the form of death safety for a term of one or more than one year. There are policies that may be for term of 30 years as well. The policy does not offer any consideration for cash value. It generally provides the largest and quick death protection on the premium dollar and the death benefits are paid in the case of a person dying within the term of a long duration.

There are several term insurance policies that are usually renewable for one or higher additional terms in a situation when the health of a person has got modified. Whenever a person renews the insurance policy for a new phrase, the premium becomes larger and in this regard, one should definitely check the rates at older age groups and the duration for which the protection can be maintained.

Term life insurance Singapore “Endowment”

If a person within a certain age group, then this type of insurance pays both the sum as well as the income to the real policy holder and in case that person dies before the expiry period of his/her age, then the particular benefit is paid to the named beneficiary. In this policy, the premium and cash beliefs are usually higher as compared to the same quantity of whole life insurance of Singapore. In other words, it can be said that the coverage linked to endowment insurance offers the least quantity of death protection to the premium dollar.

Life insurance Singapore coverage

This type of insurance offers dying protection for as long as a person has a home. The most common type among them is called as straight life and ordinary life insurance. In this type of policy, the person has to pay the same monthly premium as long as the person lives.

Thus, it becomes crucial while searching for the Best insurance provider in Singapore so as to get the maximum benefits. While making the search, Singapore Best Life Insurance Quotation can also be encountered but the decision to get the maximum benefits, thorough analysis of different types of insurance must be done properly.

Insurance Guru a group of finance enthusiasts coming together to help you get the Singapore Best Life Insurance Quotation. To know more on insurance provider in Singapore, Life Insurance Company Singapore visit our Website.

Top Benefits Of Having Life Insurance

People today are trying to cut their costs and save as much money as they possibly can. Some people are even go so far as to cut off their life insurance policy. The problem with this money saving method is the fat that you never know what might happen during your lifetime. Having life insurance does hold a variety of benefits that you can easily enjoy immediately.

One of the biggest benefits that you will receive is the fact that you will be able to leave something behind to take care of your family for life. Those who get a policy will leave a sufficient amount of money behind so that family members can cover all funeral costs as well as their monthly living expenses over a period of time. This is a very good investment to have under your belt throughout your life.

Despite what you might think, life insurance is not going to be very expensive. Most people who have their own coverage plan, even with multiple beneficiaries named do not spend more than $150 on their insurance plans. If you do not have a lot to spend, try looking into your original insurance company and see if they have any life insurance options for you to add onto your plan.

Life insurance will be cheaper if you are younger. Those who buy insurance around the age of 30 years old will be able to save hundreds of dollars a year on their coverage plan. This means that you will get a lot of insurance that will grow as an investment that you will not need for at least another 35-40 years. Look into investing as early as you possibly can so that you are set.

If you are in a little bit of a financial situation and you need some extra cash, there are ways that you can take a loan against your life insurance policy. You will need to speak with your chosen insurance company to see what type of loans they offer as well as the interest rates that you will have to pay back as well. You can also simply stop your premium temporarily in order to get on top again.

Once you sign up for your prospective coverage, your rates will always be fixed. For as long as you are alive and well you will always have the same premium price each year. If you do get to buy at an early age, that you means you will save a lot more money in the long run.

If you can afford it right now then get online and start looking for the perfect life insurance policy for you. Choose your beneficiaries wisely and make sure that you have thought about every detail in advance. The sooner you buy your policy, the sooner you can save yourself as well as your entire family heaps of money!

General Insurance Companies In India – An Excellent Introduction

The full basic Insurance carriers In India business was nationalised by Authorities of India (GOI) with the General Insurance plan Small business (Nationalisation) Act (GIBNA) of 1972. 55 Indian insurance firms and 52 other basic insurance coverage operations of other firms were nationalized through the act.

In India, insurance features a deep-rooted heritage. Insurance in numerous types continues to be pointed out during the writings of Manu (Manusmrithi), Yagnavalkya (Dharmashastra) and Kautilya (Arthashastra). The basic foundation of the historical reference to insurance coverage in these ancient Indian texts is identical i.e. pooling of sources that might be re-distributed in times of calamities including hearth, floods, epidemics and famine. The early references to Insurance policies in these texts has reference to maritime trade financial loans and carriers’ contracts.

The overall Insurance policies Corporation of India (GIC) was shaped in pursuance of Part 9(1) of GIBNA. It had been integrated on 22 November 1972 underneath the companies Act, 1956 to be a non-public company restricted by shares. GIC was shaped to manage and run the enterprise of common insurance in India.

The GOI transferred every one of the assets and functions from the nationalized typical insurers to GIC along with other public-sector insurance providers. Following a process of mergers and consolidation, GIC was re-organized with four entirely owned subsidiary corporations: Nationwide Insurance policies Enterprise Confined, New India Assurance Corporation Minimal, Oriental Insurance plan Business Confined and United India Insurance coverage Enterprise Limited.

GIC and its subsidiaries had a monopoly to the common insurance policy enterprise in India right until the landmark Insurance plan Regulatory and Improvement Authority Act (IRDA Act) of 1999 came into result on 19 April 2000. This act also amended the GIBNA Act and Insurance Act of 1938. The act as well as the amendments finished the monopoly of GIC and its subsidiaries and liberalized the insurance coverage small business in India.

In November 2000, GIC was renotified as India’s Reinsurer, but its supervisory purpose about its subsidiaries was ended. This was adopted because of the Common Insurance coverage Company (Nationalisation) Modification Act of 2002. Coming into influence from 21 March 2003, this modification ended GIC’s function as a keeping enterprise of its subsidiaries. The possession on the subsidiaries was transferred into the Government of India, which in turn divested its stake while in the companies through listings on Indian inventory exchanges.

Consequently of such reforms, GIC became the only Re-Insurer in India, and it is now called GIC Re. Indian insurance firms are needed by regulation to cede 10% of each policy price to GIC Re, subject matter to some constraints and exceptions. GIC Re has diversified its functions and is particularly now emerging being an significant Re-Insurer in SAARC nations, Southeast Asia, Center East and Africa. GIC Re has also expanded its global operations as a result of branches in London and Moscow.

GIC Re contains a rating of A- (Fantastic) from the. M. Best for its fiscal energy.

Blown Film Extrusion Introduction

Blown Film Extrusion Introduction
Blown film extrusion is a technology that is the most common method to make plastic films, especially for the packaging industry. The process involves extruding a tube of molten polymer through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene is used with this process, and other materials can be used as blends with these polymers. A diagram of a polyethylene chain is shown in Figure 1 to the right.
Background Theory on Polymers

In the cooling step of blown film extrusion, the amorphous, transparent melt crystallizes to form a translucent, hazy, or opaque film. The point where opacity begins in the bubble is known as the frost line. 
Fig 1: Model of polytheylene chain frompolyethylene Wikipedia article.The frost line height is controlled by several parameters: the air flow, film speed, and temperature difference between the film and the surroundings. Properties of the film, such as tensile strength, flexural strength, toughness, and optical properties, drastically change depending on the orientation of the molecules. As the transverse or hoop direction properties increase, the machine or longitudinal direction properties decrease. For instance, if all the molecules were aligned in the machine direction, it would be easy to tear the film in that direction, and very difficult in the transverse direction.

The Film Blowing machine Process

Fig 2: Schematic of set-up from User:J.Chiang.

Typically, blown film extrusion is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common. Figure 2 shows a schematic of the set-up for blown film extrusion. This procedure consists of four main steps: The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous liquid. This molten plastic is then forced, or extruded, through an annular die. Air is injected through a hole in the center of the die, and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film. The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter. After solidification at the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated. Advantages Blown film generally has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.
Blown film extrusion can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220 C, where as the temperature of blown film is about 135 C. Furthermore, the cost of the equipment is approximately 50% of a cast line.

Blown Film Extrusion Disadvantages Blown film has a less effective cooling process than flat film. Flat film cooling is done by means of chill rolls or water, which have significantly higher specific heat capacities than the air that is used in the blown film cooling process. The higher specific heat capacity allows the substance to absorb more heat with less change in the substance temperature. Compared to cast film, blown film has a more complicated and less accurate method to control film thickness; cast film has a thickness variation of 1 to 2% versus the 3 to 4% for blown film. The resins used for casting typically have a lower melt flow index, which is the amount of polymer that can be forced through a standard die in 10 minutes according to a standard procedure. The melt flow index for cast film is about 5.0 g/10 min where as for blown film it is about 1.0 g/10 min. Consequently, the production rates for cast film are higher: cast film lines can reach production rates of up to 300m/min where as blown film lines are usually less than half this value. And finally, cast film has better optical properties, including transparency, haze, and gloss.

Common Problems Air entrapment between film layers and rollers – this may cause film scratching or wrinkling, or processing problems when winding up the film due to reduced friction. Possible solutions to this is using a vacuum to remove entrapped air or by using winding rolls with a diamond shaped groove in the rubber cover to increase surface area and decrease amount of entrapped air in the film. Large output fluctuations from the die – this causes thickness variations, and can be prevented by keeping the extruder clean and by using more consistently shaped pellets in the extruder. Melt fractures – these appear as roughness or wavy lines on the film surface, and can be eliminated by lowering the viscosity of the polymer melt. This can be done by increasing the melting temperature or by adding an internal lubricant to the material composition. Thickness variations in the film – this can be avoided by centering the die in the extrusion line before every run, adjusting the air speed of the cooling system, or by using heated die lips. Die lines on the surface of the film – this defect reduces the aesthetic appeal of the film, reduces optical properties, and weakens mechanical properties such as tear strength. This can usually be avoided by routinely cleaning the inner surfaces of the die and by refinishing scratched or roughened flow surfaces. Gels – these defects are small, hard globules encapsulated in the film or stuck on the film surface and reduce the aesthetic appeal of the film and cause stress concentration points which may result in premature failure. These are caused by overheating to the point of polymer degradation in the die, and can therefore be avoided by cleaning the inner surfaces of the die on a regular basis. Optimization of the Process Coextrusion One way to improve the line efficiency of blown film extrusion is to implement coextrusion. This is the process of extruding two or more materials simultaneously through a single die. The orifices in the die are arranged such that the layers merge together before cooling. This process saves time because it extrudes two or more layers at the same time, and it provides a method with fewer steps to produce multilayer films. The production rate for a coextruded multilayer film of three layers is about 65m/min, and the production rate for a single layer of blown film is about 130m/min. Thus, in order to produce 10 000m of a three layer multilayer film, it would take almost 4 hours using a single layer blown film process, and only 2 and a half hours using the coextrusion process. Furthermore, the film produced from the single layer process would require an extra step to glue the layers together using some sort of adhesive. Coextrusion is the least expensive means of producing layered films and the coextrusion system is capable of quick changeovers to minimize production line down time.

Minimizing the Melt Temperature
The efficiency of blown film extrusion can be improved by minimizing the temperature of the polymer melt. Reduction of the melt temperature causes the melt to require less heating in the extruder. Normal extrusion conditions have a melting temperature at about 190 C despite the fact that the temperature of the melt only needs to be about 135 C. However, it is not always practical to decrease the melting temperature by that much. By decreasing the melt temperature 2 to 20 C, the motor load can be decreased by about 1 to 10%. Furthermore, reduction of the melt temperature causes less need for cooling, so there is a reduced use of the cooling system. Moreover, removing heat from the bubble is usually the rate-limiting factor in this extrusion process, so by having less heat in the polymer to remove, the rate of the process can be increased, thus yielding higher productivity. A way to maintain the melt temperature at a minimum is to choose an extruder that is matched to the specific processing conditions, such as the material of the melt, pressure, and throughput.

Heated Extrusion Die Lips
Typically, solutions to melt fractures involve decreasing the output or increasing the melt temperature to decrease the shear stress in the extruder. Both of these methods are not ideal because they both reduce the efficiency of the blown film line. Heated extrusion die lips can solve this problem. This targeted heating method allows for film extruders to be run at higher production rates with narrower die gaps while eliminating melt fractures. Direct heat is applied to the surface of the polymer melt as it exits the die so that viscosity is reduced. Therefore, melt fractures, which are caused when trying to extrude too much of the polymer at one time, will no longer act as a limiting factor to increasing the production rate. Furthermore, heated die lips use less energy than increasing the melting temperature because only the surface of the melt is heated and not the bulk of the liquid. Another benefit of using heated die lips is that thickness variations can be controlled by adding heat to certain areas along the die circumference to make the film at that position thinner. This would ensure that no excess material is used.
Determine how much energy each of these processes can save per given volume of material. 

Above article from www.appropedia.org

Kingdom Machine Co.,ltd Ruian Economic Zone,Wenzhou,China 325200
Mobile:0086-13958812663;  0086-13088651008
Tel.:0086-577-65127709       Fax:0086-577-56846789 Whatsapp:0086-13958812663
sale@kingdommachine.com www.kingdommachine.com www.chinablownfilmextrusion.com

How Market News Affect Business And Investment Decisions

News has become a part and parcel of modern lifestyle. No matter whether you are watching television news or reading a newspaper or reading news stories at a news portal, the objective is the same getting updated with what is happening around you in all aspects. Businessmen, investors, and corporate people give more importance on business news rather than other news. And for investors and businessmen in the Indian market, business news on India caters to their thirst for information every now and then. Most people rely on a market news portal that carries detailed information related to business news on India. The greatest advantage of reading news at such a platform is that you can read a relevant news article several times and browse through the numerous pages at ease to your hearts content and to your convenience.

The influence of business is such that even those who are not involved in any stock market investment or business do read business news on India. In the future if they happen to start investing, they will set sail easily no matter what the tide is. To assess the direction of a trend, especially for short term and long term trading, collect statistical data records of market fluctuations over a certain period of time.

You can also view the up-to-the-minute currency exchange rates at a market news platform. Almost all financial sites do run online calculators to help you calculate the currency values and thus find the currency exchange rates of the desired countries. For international traders and forex traders, getting updated with the latest currency exchange rates is a must. Once you are updated with market news, will no doubt stay away from confusion in case of taking an investment decision.

The activities in the money market change according to what the investors do with stocks and commodities. There are varied investment options in the market today. If you read market news regularly you will know about the latest investment products as well as existing ones that are lucrative. This way you can diversify your investment plans and facilitate yourself and your family with a secured present and future.

Boat Loans And Boat Finance

Financing your next boat is a very important process, as you want to choose a finance package most suitable to you. There can be many things to check including
Boat loan interest rate
Fees and charges
Break fees if you paid it out earlier
Can you pay extra payments
Time it will take to approve and settle your boat loan
Does the boat finance company suit your criteria to approve the finance

You can have unsecured or which can affect the cost of your loan.

It can be a requirement of the boat finance company to have fully comprehensive insurance on your boat before purchase and while you pay off your boat loan.

Finance companies can assist to ensure you have a hassle free boat purchase and help with
Encumbrance checks to ensure that there are not any outstanding loans from the prior owner left against the boat.
Title check or confirming the ownership of the boat you are purchasing.
Clear transfer to seller of the amount financed on the boat purchase. .
Boat loans, subject to the finance companys approval can be financed to the full cost of the purchase including
On-road costs and taxes.
Boat Insurance
Marine breakdown warranties
Loan protection for death, disability and unemployment.
Older boats can be ok. Boat finance can apply for all ages new and used depending on the boat loan lender.
Finance structures can be flexible to suit your circumstance. Options to consider on your boat loan could be
Delayed payment boat loans so you first payment starts at a extended time into your finance contract
Interest only payment options including balloon payments.
Extended finance terms
Structured boat finance payments to suit your life style or your work cash flow
Construction boat loans
There are many marine finance options available for imported boats.
Commercial boat finance options are available that could be suitable for business use. Some factors to consider that relate to business car financing are:
Chattel mortgage boat finance

The structure of your business car finance can affect your taxation claim.
Dealing through a reputable boat loan broker can give you a choice of boat finance lenders. It is important to know that you may get boat loan interest rates and loan fees and charges cheaper than banks.

Make academic portfolio more valuable with finance degree online

Have you ever dreamt to work in a top-notch financial firm and earn high salary job? If yes, then don’t waste your time and enroll your name in an online university to earn finance degree. As the businesses are expanding nowadays with fast rate, so finance degree holders are also in demand to handle the finance operation in a prominent way. Finance is the backbone of an origination which helps to make an accurate strategy for an organization and helps to grow it in a right direction.

Academic profile The academic structure of finance degree includes various streams like International Securities, Investment, Capital Markets and Banking, Regulation and Compliance, Corporate Finance, Financial Engineering and others. Finance Degree from online mode is offered by almost all universities at Associate, Bachelor’s, Master’s and doctorate level. Online mode is the best way for the students who don’t get time for the traditional classes. The degree at bachelor’s level will give you opportunity to start your job as a fresher whereas if you have acquired master’s degree in finance degree, then you will get many prestigious positions at higher levels. If you opt for finance specialization at Master’s degree in Business Administration then it would be wise investment for your career, as this professional degree would give you a plenty of job prospects at managerial level.

Some of the popular university which offer finance degree online are listed as below: Walden University University of Phoenix Capella University Kaplan University Florida tech university online Upper Iowa university

Employment opportunities Finance degree from online mode assures reputed job in top-notch financial firms with high paying job. It opens lots of employment opportunities in several sectors like commercial, education, non-commercial, IT, media, public and non-profit organizations. Moreover, aspirants get esteemed positions in different companies as a finance manager, Accountant, financial planner, Auditor, financial analyst, financial advisor, Credit analyst, Chief Financial Officer (CFO), Certified Public Accountant (CPA,) investment banker and others.

Start your business After holding finance degree, you can even start your business and give financial advice to other companies. With your own skill and knowledge of finance operation, you can find out the excellent path and develop your business accordingly. Aspirants can work outstandingly with their dynamic approach and plans to get high Return On investment (ROI) in each financial year.

Conclusion If you are a working professional and want to update your resume, then Finance Degree from online mode is the best way to make your academic profile worth a look. The degree provides you required skills, tools and techniques of financial operation which are essential to make finance strategies for a company.

Pradeep is a educational consultant who provides the information for students and proffessionals . He gives a lots of article like Finance degree online and others . For more information you can visit on this site uiu.edu .

Types Of Vehicle Insurance In India

Today, anybody and everybody, has insurance of some sort. Either they believe in insuring themselves and their loved ones, or in insuring their vehicles! In India and in most other places, vehicle insurance is mandatory. The amount your vehicle can be insured for varies depending on the insurance companies and the insurance brokers.
In India, there are several types of vehicle insurances. Companies in India offer insurance at four levels.

1.Fully comprehensive vehicle insurance- This is by far the most expensive insurance, yet the most common type, as it covers all the possible damages and costs that your vehicle may incur. This type of vehicle insurance proves to be advantageous as there is no need to produce proof of the damage to claim the insurance amount. Thus, if your vehicle is damaged or stolen in your absence, then you can still approach the insurance company.

2.Third Party insurance- This type of insurance carries a comparatively cheaper premium and insures against damages and legal claims when you are at fault and have hit a third party. The insurance company is not responsible for any other scratches or occurring that takes place with your car.

3.Specialized car insurance- This type of insurance refers to any car that is over 25 years old, as vintage cars have different needs and requirements. Similar to a comprehensive auto insurance policy, the only difference between the two is that you are limited to an x amount of miles in a given year.

4.Third Party Fire and Theft insurance- Befitting to its name, this insurance covers the costs of your vehicle in case of fire, theft, accident, etc. However, in case of an accident, the insurance company will only pay up if you are at fault and have hit another car and not vice-versa.

In order to go forward with insuring your car, you need to carefully go through the various schemes offered by different insurance brokers. Each insurance broker has a scheme that offers one policy better than the other. A way of going about the entire process would be to patiently go through all the possible offers, look out for the best premium offered and then insure your vehicle. Today, online access to insurance schemes makes the process a whole lot easier.